The Eternal Maker Crafts

Tuesday, 22 April 2014

New Deliveries! And A Babygrow Play-Cube Tutorial

Well a lot of things have been happening at The Eternal Maker since we last spoke, as always we've had lots of lovely new deliveries of fabric but we've also had some bigger events going on in our lives too, like planning a new roof for our shop and one very special new delivery - our first Eternal Maker baby!
Yes, we are pleased to announce that our shop manager Rachael had a baby boy shortly after Christmas last year, so in his honour, here's a simple make, for all new arrivals. It can be made with cotton jersey fabric or upcycled babygrows - a lovely way to get more use from those first favourite outfits!

You will need:

At least three babygrows or vests (we used four, first size, vests)
Or..... a selection of any other fabrics. Cotton jerseys give you a lovely soft finish and organic options are great for chewing too! (One long quarter will be enough for your cube but it will look nicer if you use a variety of fabrics) Brushed cottons or minky-type "cuddles" fabric will give you fun textures for feeling.
One long quarter of Vilene
Some toy stuffing
Needles and thread and/or sewing machine
Scraps of "Bondaweb" if doing any applique
Jingle bells and child proof pot, or teddy squeakers, are optional

1) If you are using fabric by the metre skip to next instruction.
If you are using babygrows or vests, start by cutting away any seams and poppers, leaving the largest pieces of flat fabric you can. From vests you will get one piece from the front and one from the back. From babygrows you may get two pieces from the front or back.
 
2) Measure your fabric pieces to work out the largest size square you can cut from them. We managed to get 6" squares. Cut six 6" squares (or your required size) from your Vilene and mark 1/2" seam allowance guides on all edges with a pencil on the side that ISN'T iron-on (as shown in the picture below). Iron these Vilene squares onto the reverse of your vest or fabric pieces. We have placed some diagonally because we wanted the stripes on the finished cube to be diagonal.
3) Iron the Vilene squares down on the reverse of your fabric and cut out the fabric following the edges of the Vilene. You will need 6 squares to make your cube.
4) We wanted to be a bit fancy and add some applique - if you don't want to do this skip to instruction number 8.
These vests had little animal pictures on that we wanted to use. We cut a heart shape from "bondaweb" that matched the size of the applique we wanted to attach. Then we ironed this on the reverse of the picture - making sure to centre the picture as best as possible.
5)Then we cut out the heart shape from the fabric following the edge of the ironed-on "bondaweb" heart. Removed the paper backing and then ironed on the hearts onto the centre of a couple of the cube squares.
6) So you should now have 6 Vilene-backed squares with any applique on you fancy.
7) Use a small zig-zag stitch to sew on any applique.
8) Start stitching the squares together. Lay them with right sides facing each other and stitch together, following the 1/2" seam allowance guide. Make sure you begin and finish you stitching where the two seam allowance guides cross (otherwise your cube's corners won't work).
 

 
9) Continue joining squares to form a cross shape.
 
10) When you join the squares next door to other squares make sure to stop where the seam allowance guides cross - this will give you a nice sharp corner.
 
 
 

11) Keep working - stitching all the seams together - pulling your work up into a cube as you go. Be careful to only ever sew through two layers of fabric - it's easy to catch another layer in your stitching near the corners so make sure extra layers are pulled out of the way as you go.
12) Make sure you leave a gap in the final seam you join for turning. To keep your corners sharp - leave this gap in the centre of one seam and stitch together the final corners as before.
13) Tie off any threads and turn your cube the right way out.
14) We wanted our cube to rattle so we placed jingle bells inside a child-proof pot and put this inside the cube, well surrounded by stuffing. This is entirely optional, if you are not happy using a child-proof pot you could add teddy squeakers or just stuff the cube normally. Make sure you push stuffing hard into the corners of the cube to help it keep it's shape.
15) Sew up the hole you stuffed your cube through and you're finished!

All you need now is to find a small person to enjoy it!


 
 

Labels: , , , , , , , , , , , , , , ,

Friday, 14 June 2013

Simply Bootiful Booties

So I first made these booties a few years back, and then sort of lost track of it as a project.  You know how you do - you makes loads of one thing, then none for ages until you forgot that it was something you ever did.  And then rediscover it thinking - why did I ever stop?  (I do the exact same with food.)
I guess I thought about it again because this year is turning out to be a baby year.  Do you have baby years?  The years when everyone you know is having a baby.  Some years are wedding years (last year) and some are baby years.  This year, two of my best friends are having babies, and my brother is too.  And there are suspicions of another friend, but she's denying so we won't go there.  And those are just the people in my inner circle, so to speak.
So all my projects at the moment are baby based.  You may have noticed this, to be honest.  I have only just realised it myself, but you guys may be a little quicker than me.
Oh well... here's another!
You will need: 
Template - you can find it here 
20 x 30cm outer fabric - we used this
20 x 30cm inner fabric - we used a lovely hot pink kona cotton
15 x 20cm plain linen
15 x 20cm fusible fleece and cuddle fluffy fabric - fuse together before cutting out
1/2m 1/4" wide elastic
 1.  Cut out your outer template pieces - 2 from your top fabric, 2 from your lining fabric.  Then cut 2 x 3cm strips from your remaining fabric, each approximately 12cm long.  
2.  Fold a 1/4" edge on each long side of your strips, fold in half, and insert your lengths of elastic, pushing right up against the fold.  Pin along the edge, trying not to catch the elastic (diagram 2).  
 3. Sew along the edge of the strip, being careful not to touch the elastic.  Stitch on one end through the elastic and the fabric, about 1cm in, then pull the elastic a bit, so the fabric bunches up nicely.  (diagram 3)
 4. Stitch on the other side, and trim.  Do this for both strips, so you have one for each shoe.
 5.  Right sides together, pin your 'u' shaped outer and your 'u' shaped lining fabrics together.  On one side, about 6cm down, pin in your elasticated strip (see diagram 5)
 6.  Sew down and across the elastic catching it in place.  Stop just past the bottom of the 'u' - so about 2/3 of the way around.  You can just about see this in diagram 6.
 7.  Ignore diagram 7.  Apparently I made 2 diagrams the same. Hmm..
 8.  This is where it gets a little complicated.  Take the loose end of your elastic, and pull it round to the other side, and feed it in so it is level to the already sewn end.  Pin it into place.  All your fabric will bunch up in the middle, and you'll probably get a little frustrated, but hang in there.  See diagrams 8, 9 and 10
 9.  Now sew down from the other side to join where you sewed to before.  (diagram 11)
 10.  This is hard to see because the elastic is pulling it all about - but the next step is to clip your curves.  Trust me, this makes a big difference, reducing bulk in your seams and making them lie flat.  Excess bulk on such a small project can show up a lot.  Trim the bulk on the elastic too.
 11.  Your shoe will now look something like this (diagram 13) - ie, not much like a shoe.  Don't worry.  A shoe will come.
 12.  And like this from the other side.  Still not much like a shoe.
 13.  Turn your shoe the right way out - and finger press the seams.  You may find pinning it into place makes it easier to control.
14.  Pull open the un-sewn straight  edges, and line up against each other right sides facing - outer fabric to outer fabric, lining fabric to lining fabric, making sure to line up the centre seam.  Sew down this line (diagram 15a).  Turn the right way out again, finger pressing the seam.

 15.  Using the template, cut out your sole pieces from the fused fluff and fleece, and the linen.  Cut 2 from each fabric.
 16.  Take one linen piece, and one fluff and fleece piece, and wrong sides facing,  lay them together.  Stitch all around the edge with a very small zigzag stitch.  Diagram 17.
 17.  Pin the right side of the upper shoe to the linen side of the sole.  Pin all around at intervals.  (diagram 18).  If you find that your upper has a little too much excess fabric, go back to the back seam and make a little smaller. 
 18.  Sew around using a scant 1/4" seam, catching all layers.
 19.  Turn the bootie the right way out and then repeat the whole process for the other bootie. 
I have to apologise slightly because I think in my write up of this tutorial I've made it sound super hard.  It's not, it's just a little fiddly and hard to explain.  But ultimately very satisfying, I promise!  Because check it out - look how amazingly and ridiculously super cute they are.



Labels: , ,

Tuesday, 7 May 2013

Stash busting Bandana Bibs - Tutorial

It's always about this time of year that for some reason all the projects I start seem to be baby related.  I don't have a baby of my own (and at this moment in time, I'm pretty good with that, too), but as I type this two of my best friends and my brother are having babies. (Not my brother personally, of course, but you know what I mean.)  So at least I have people to make all my baby projects for.
And why do I love baby projects?  So many reasons.  The first being that they are usually very quick.  I'm all about the quick.  I don't have the time or patience for a quilt that takes years.  Give me a weekend project and I'm in.  Number 2 reason - things are usually pretty small so don't take much in the way of supplies.  They're often good stash busters.  Number 3 reason - well, it's all just so very cute, isn't it?  I could go on, but I won't.
So this project here is a super simple bib.  You can run multiples of these up in an hour.  Now that's my type of project!  It's one of those projects that uses up small amounts of fabric.  Those small amounts you have sat at home that aren't really big enough for much else but they're still big enough not to throw away - you all know what I'm talking about.  A fat quarter will be enough for 3 or 4 of these.

You will need:

30x30cm print fabric.  We used double gauzes and jerseys for extra added softness, but any craft cotton will also do.
30x30cm terry cloth - such as this
Poppers/ Snap fasteners - you will need 2 of 1 side and 1 of the other, so 3 full sets will do 2 bibs.
This template

So here's how:

1. Using the template - cut out 1 triangle of patterned fabric and one of terry, and lay them right sides facing each other.  Pin all around.  It's a good idea to over pin when using stretch fabrics, or fabrics with a loose weave.
2. Sew around the edge using a 1/4" seam allowance.  Leave a 2" gap for turning. 
3. Once you've sewn, turn the right way out through the turning gap.   Once you've done this, poke all the corners out properly, so they're nice and rounded.  Then pin all around the edge again.  This will help sew it up, and stop one side bagging as you sew.  Topstitch all around the edge, catching your turning gap in your stitches.

4. Sewing on your poppers.  Sew one side of a popper to one side on the patterned fabric side of your bib.   On the other side of the bib, sew 2 other sides of popper to the terry cloth side.  Position them about an inch apart.  These two poppers will give you a little ease for sizing.  Make sure to secure these firmly as hopefully it will be used a lot!

 
 5.  Repeat and make lots more!  A stash of these little dribble bibs makes useful on hand presents.

Labels: , , ,